Author Topic: What about this Dutch press?  (Read 11395 times)

Annie

  • Guest
What about this Dutch press?
« on: November 12, 2012, 05:57:37 PM »
I aboslutely hate the presses I have since I have no idea what the pressure is and they are extremely difficult to take apart, so I have been considering a Dutch press.

So I found this one:
Which seems to meet my criteria of being affordable and Dutch.

This is what it says:
Quote
The calibration numbers are at each notch. The end notch provides 4 times the weight in pressure on the follower. We have tested the arm with 50 LBS of weight at position 4 therefore creating 200 PSI at the follower! You will never need this much! As most recipes for hard cheese are for 2lb batches using a 4.5 inch mold, we have included a chart which enables you to easily use the correct amount of weight for any mold from 4-7 inches in diameter. The larger the diameter, the more weight is required to apply the same amount of pressure per square inch on the curds. (We use 2.5,5 and 10 pound barbell weights purchased at Wal- Mart, then tie a stainless steel wire loop to them to hang them. Fabric or rope could also be used)

Is that sufficient weight?


Quote
A 6 inch diameter mold recycled from food grade plastic and maple follower:
The mold has the necessary drainage holes. The mold will hold the curds for a 2-4 pound cheese and creates a nice looking hoop of cheese which will dry and age evenly. 


If I made two cheeses at one time (not unknown when I get backed up!), could I put them on top of each other in the mold and have the whole thing work out?

Thanks for any advice!

hoeklijn

  • Guest
Re: What about this Dutch press?
« Reply #1 on: November 12, 2012, 06:36:10 PM »
Annie, I guess something went wrong with the image, there's nothing to see....
I made a press myself (hey, I'm a Dutchman!) and there are formulas to calculate the pressure:
Distance from henge to the "stamp" is 7cm, from stamp to the end of the lever is 35cm, 35/7=5.
The way I use pulleys multiplies the pressure twice, so 2 x 5 = 10. So 1 lbs will be 10 lbs on the mould (which is NOT the psi!)

Offline smolt1

  • Mature Cheese
  • ****
  • Location: oregon
  • Posts: 246
  • Cheeses: 29
  • Default personal text
    • SturdyPress.com
Re: What about this Dutch press?
« Reply #2 on: November 14, 2012, 04:57:33 AM »
Annie

50 lbs of weight on the lever arm creates 200 lbs of pressing weight, not 200 PSI of pressure. 200 lbs of pressing weight on a 6 inch diameter mold is 7.07 PSI, close to what you need for Cheddar.

Offline Boofer

  • Old Cheese
  • *****
  • Location: Lakewood, Washington
  • Posts: 5,015
  • Cheeses: 344
  • Contemplating cheese
Re: What about this Dutch press?
« Reply #3 on: November 14, 2012, 03:31:04 PM »
I made a press myself (hey, I'm a Dutchman!)
Wow, a Dutchman actually making a Dutch press!  8)

Hey, Herman, have a cheese. You da man!

-Boofer-
Let's ferment something!
Bread, beer, wine, cheese...it's all good.

Tobiasrer

  • Guest
Re: What about this Dutch press?
« Reply #4 on: November 16, 2012, 04:47:35 AM »
Here is my press I just built, it has 6 bolts (One to hold the arm and one for the 'foot' that presses the mold, and 4 to hold the upright on)
The 6 bolts come out and it comes apart easy for storage. There are a few upgrades I will make with my ext, like a bit bigger at its only able to fit a 7" mold between the up rights, But so far I am happy, and so is my wife cuz it isnt in her way al the time LOL

hoeklijn

  • Guest
Re: What about this Dutch press?
« Reply #5 on: November 17, 2012, 10:39:02 AM »
Thanks for the cheese, Boofer. It's some time since I used it. Besides the Reblochon 6 weeks ago and the Cambozola 2 weeks ago I didn't make any cheese. Busy busy busy...
@ Tobiasrer: Smart design, cheese for you. I make a shelf above my cave where I can store it...

Offline mdmoore00

  • Medium Cheese
  • ***
  • Location: Butte, MT USA
  • Posts: 28
  • Cheeses: 5
  • -- Matt --
Re: What about this Dutch press?
« Reply #6 on: December 17, 2012, 04:18:31 PM »
In an attempt to create a press that is affordable I designed this press. It is simply a force doubler, 10lb at the notch is 20 lb at the mold. By adding a couple pulleys the mechanical advantage could be greatly increased. I made it of #2 fir from my local (Butte,MT, USA) lumber yard at a cost of $12. The base is to short to self support, so I clamp it to the counter top. It is large enough that I can fit my small cooler under it and insulate the cheese during the press. I have had great success with this in the current configuration, but I plan on adding a few pulleys to increase the mechanical advantage. Here is a picture and the plan in inches (sorry metric friends). 

Offline Al Lewis

  • Old Cheese
  • *****
  • Location: Port Orchard Washington
  • Posts: 3,285
  • Cheeses: 179
    • Lou's Food & Drink
Re: What about this Dutch press?
« Reply #7 on: December 17, 2012, 05:33:12 PM »
If the press you are talking about is the one sold here   http://cabarrusfarms.com/   I just bought one.  I really don't see me ever needing more than 200 pounds to press the cheeses I make and I liked its simplicity in calculating the weight.  It has arrived and looks very nice and does come with a chart to convert PSI to actual weight.
Making the World a Safer Place, One Cheese at a Time! My Food Blog and Videos

xyztal

  • Guest
Re: What about this Dutch press?
« Reply #8 on: December 17, 2012, 07:12:40 PM »
The press looks so pretty!!!! 

RIght now I am just using food bucket with lead (from the bullet...)

Mighty Mouse

  • Guest
Re: What about this Dutch press?
« Reply #9 on: December 18, 2012, 03:56:34 AM »
The press looks so pretty!!!! 

RIght now I am just using food bucket with lead (from the bullet...)

Uhh... lead? Around food?

Yeah, dutchpress might be a very good idea- ditch the lead.

xyztal

  • Guest
Re: What about this Dutch press?
« Reply #10 on: December 18, 2012, 04:03:35 AM »
Nono,I put one food pail on top of the other, and put the lead on the top pail....

Mighty Mouse

  • Guest
Re: What about this Dutch press?
« Reply #11 on: December 18, 2012, 04:12:07 AM »
Nono,I put one food pail on top of the other, and put the lead on the top pail....

That's good. Still though, I would be really hesitant about having lead anywhere near any kind of food products. I used to have a similar setup but with bricks. Worked alright for me.

Offline Al Lewis

  • Old Cheese
  • *****
  • Location: Port Orchard Washington
  • Posts: 3,285
  • Cheeses: 179
    • Lou's Food & Drink
Re: What about this Dutch press?
« Reply #12 on: December 18, 2012, 03:01:17 PM »
If you're using that lead to cast bullets that can also be a problem if it's in the vicinity of your cheese, or any food.  Molten lead can, and will, become airborne.
Making the World a Safer Place, One Cheese at a Time! My Food Blog and Videos

drifterdon

  • Guest
Re: What about this Dutch press?
« Reply #13 on: January 18, 2013, 12:21:48 AM »
If the press you are talking about is the one sold here   http://cabarrusfarms.com/   I just bought one.  I really don't see me ever needing more than 200 pounds to press the cheeses I make and I liked its simplicity in calculating the weight.  It has arrived and looks very nice and does come with a chart to convert PSI to actual weight.


So Al,
How do you like this press so far?
I am in the market for a new one because mine makes lopsided cheese and I too like this one.

Don

Offline Al Lewis

  • Old Cheese
  • *****
  • Location: Port Orchard Washington
  • Posts: 3,285
  • Cheeses: 179
    • Lou's Food & Drink
Re: What about this Dutch press?
« Reply #14 on: January 18, 2013, 12:46:15 AM »
I like it just fine.   :D  Please read here .
Making the World a Safer Place, One Cheese at a Time! My Food Blog and Videos